Wheels

Zipp Speed Weaponry Freehub Bodies - Material: Aluminum

- Replacement straight pull spokes for Zipp 88 (Front) and 188 (Rear) Hubs

- Cold forged 304 stainless steel with rolled threads - Lightweight 2.0mm/1.7mm/2.0mm double-butted form - Nipples sold separately - 172g (32 spokes @ 262mm) - Bag of 50

- Cold forged 304 stainless steel with rolled threads - Lightweight 2.0mm/1.7mm/2.0mm double-butted form - Nipples sold separately - 172g (32 spokes @ 262mm) - Bag of 50

Our thru-axle kit comes with everything you need to mount most 12x142 thru-axle bikes on your KICKR SNAP indoor trainer. This accessory will work with all editions of the Wahoo KICKR SNAP. It includes the following: - Threaded axle spacer M12 x 1.75 Coarse - M12 x 1.5 Medium - M12 x 1.0 Fine - End Cap

- High performance adhesive tape, a great pairing with Velox Cement - Each roll is usually adequate for gluing two tubular tires - Protects tube from spoke/nipple/rim puncture

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

Stan's 3.30/3.30Ti Hub Kit converts Stan's 3.30 front hubs from quick-release to through-axle compatible. Installation is easy—just pull the old ones off and put the new ones on. Conversion kits available in 12mm and 15mm.

Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.

Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed. - 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration - Chromed steel bearings - Wide bearing stance and axle design reduces flex and adds durability - Low drag main seal prevents contamination and reduces resistance - Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

Sta Tru Front Wheel - Measures 9-inch across, uses a 12-inch tire - Single Wall Rim - Hub/Brake Compatibility: Rim Brake - ISO Diameter: 203 / 12.5-inch - Front Axle: 5/16-inch x 85mm - Rim Width (Internal): 24 mm - Tire Type: Clincher

Sta Tru Rear Wheels - Single Wall rim - Wheel Size: 20-inch - ISO Diameter: 406 / 20-inch BMX - Valve: Schrader - Tire Type: Clincher

- STW ST1 26.5mm wide alloy rims - KT QR ATB 9mm/100/108 axle - Black or Silver UCP spokes

The trails in our neck of the woods get pretty hairy pretty fast, so we've found them to be the perfect testing ground for fast and tough wheels like our Traverse 29 Carbon. The steep climbs and descents helped inspire some pretty radical designs, and most importantly, left us with no doubt that these wheels will exceed your expectations. Let's talk about those expectations. They include everything from the ability to stay true after launching off drops to being light enough to efficiently pedal to the top of a climb, and they all begin with the rim. Our engineers knew they wanted carbon fiber, and with the inclusion of our Zero Bead Hook design, they were able to implement a continuous fiber layup across the sidewall and rim bed. And when paired with a whopping 30-millimeter internal rim width, they made a wheel that's super resilient to impact with low rolling resistance and incredible traction. You'll also find that it helps prevent "burping" during hard cornering, while also making tubeless set up quick and easy. Along with light overall weight, stiffness, and durability, another top priority for the Traverse was ease of use. First off, we got rid of the creaky straight-pull spokes and corrosion-prone alloy nipples. Next up, we landed on 28 J-bend spokes, for front and rear wheels, that are all the same length, making it easy to find replacements if needed. And finally, we engineered a new hub design with a wider profile and higher flange to aid in overall stiffness. A wider rim does a variety of things for ride performance, better supports the tire for increased confidence and grip, and it affords you the ability to run lower pressures that help spread impact out over a larger surface area to reduce the risk of damage. And when you combine this girth with the notoriously fast rolling 29 platform, you're left with an incredibly stiff, quick to accelerate wheelset that climbs just as well as it shreds descents. After designing the perfect trail rim, we kept our lightweight and durable design properties in mind with the wheel build, hand-lacing the rims with DT Swiss 350 Classic hubs via 28 DT Swiss Competition Race spokes and brass Pro Lock nipples. Inside, you'll find sealed cartridge bearings and a 36t quick engagement ratchet system for quick accelerations. We also wanted to ensure that each wheel was built correctly, and we found that this could only be achieved by hand. Machines, we found, have a tendency to miss little mistakes that humans catch. Each wheelset comes packaged with a SRAM XD driver, 11-speed freehub, and a tubeless valve stem in order to make tubeless set up a touch easier. *Please note that Shimano freehubs are sold separately. - Assembly Method: Hand built at every step; from rim layup to the last nipple turn. - Bearing Type: DT Swiss Sealed Steel Cartridge Bearings - Extras: 19 and 31mm OD end cap options included, Roval tubeless tape and tubeless valve, Spare Spoke and Nipple Kit, System Weight Limit: 240lbs / 109kg - Hub: Roval DT Swiss 350 J-bend, 6-bolt, Star Ratchet 36t internals (10 deg), 110x15mm & 142x12mm thru-axle, SRAM XD Freebub, (Convertible freehub and endcaps) - Nipple: DT Swiss Hex Prolock Brass 2.0x14mm - Rim Details: 25mm Depth, 35mm External Width, 30mm Internal Width, ERD 594 - Rim Type: Traverse Carbon, 29, Disc Brake, Tubeless Ready, Zero Bead Hook Design - Spokes: DT Swiss Competition Race J-Bend, Front: Two-Cross 28 count, R: 282mm, L: 279mm, Rear: 282 Two-cross 28 count, DS: 280mm, NDS: 281mm - Tire Size: 1.95 - 3.0 - Max Pressure: 40 psi - Weight: Wheelset 1,800g (including tubeless rim tape and tubeless valve)

650b bikes are all about fun and nimble handling, and the Specialized Stout XC 650b wheels delivers on this in spades—no matter if you're just getting started or you're a seasoned trail rider. It's been built tough to meet the rigors of mountain biking head-on, while the nimble wheel size guarantees a good time. It features a durable, double-wall alloy rim construction that adds strength without stacking on the weight. And to ensure that you'll be able to stop once you get motoring, the wheels are both disc-compatible. High value just met high performance. - Disc-compatible hubs can also be used with traditional rim brakes - Double-wall rims are strong and durable - Machined braking surface creates superior stopping power in any condition - Stainless spokes won't rust, easing long-term maintenance - 8-/9-speed cassette rear hub provides plenty of gearing options for climbing and riding the flats

The new Stout XC SL 29 front wheel includes a strong, double-wall alloy rim, stainless steel spokes, brass nipples, and a reliable Shimano Center Lock hub. Charcoal decals complete the look, making this a perfect OE replacement or XC-ready upgrade. - Lightweight and reliable Shimano hub. - Double-wall, disc-specific rim is strong and durable. - Brass nipples hold spoke tension securely and resist rust for added durability. - Stainless spokes won't rust, easing long-term maintenance.

SPANK Industries Fratelli Tape is a special ultra-light polyamide, adhesive tubeless conversion tape, which is ideal for SPANK's patented OohBah profile rims. Thicker, less pliable tapes are often difficult or impossible when taping complex rim profiles. Fratelli tape makes tubeless set up simple, and adapts well to a variety of rim types, including sleeved and welded joints. 25mm width tape is suggested for rims up to 29mm internal width, and 30mm tape for rims 30mm internal width and greater. With adhesive properties unaffected in a wide temperature range, Fratelli tape is also perfect for winter riders, or those in exceptionally hot environments. - Material: Ultra Thin Polyamide - Width: 25mm or 30mm - Features: high temperature range adhesive, ideal for complex rim profile Installation: - Affix tape all the way around on the right side snug against the bead hook - Then repeat a second circumference around the left side, providing double-thick coverage over the spoke holes - Use a red-hot awl or similar to pierce the valve hole

- Replacement rear wheel skewer. - Specifically designed for use with Saris trainers. - Can be used for both indoor and outdoor rides.

Feel your bike come alive on the open road with the new Alpinist CL II, featuring the lightest, best-handling clincher rims we have ever made, elevated with the performance of a tubeless system. The brand new Alpinist CL II now brings mountain-taming performance slightly closer to earth with a carefully selected build designed to let riders take full advantage of the low rim and spoke mass. The Alpinist CL II utilizes the same rim as the alpinist clx ii. They react to even the slightest increase in power with immediate acceleration and carve the purest lines in the corners, yet they can also handle almost double the impact standards of every certifying body. The result is a 1375-gram tubeless wheelset with an otherworldly ride quality designed for real-world road pressures. The Alpinist CL II utilizes components curated to keep you rolling and rolling fast. The DT Swiss 350 hubs, featuring their star ratchet drive system, are reliable and easy to service, while 24 DT Swiss comprace straight-pull spokes front and rear, laced to the rims with their alloy pro lock nipples, are synonymous with reliability and can be obtained at any bike shop. The reduced rolling resistance of a tubeless setup is undeniable, as are the benefits of improved handling and incredible puncture protection. It took the most extensive and demanding engineering and testing program we've ever undertaken. As a result of this extensive development, the Alpinist CL II features a hooked rim that can handle a huge range of pressures up to 110psi and offers an easier set up and mounting experience than ever. - Rim: Alpinist CLX Carbon Clincher, 700c, Disc Brake, Tubeless - Rim Details: 33mm Depth, 27mm External Width, 21mm Internal Width - Hub: DT Swiss 350 Straightpull Center Lock, Star Ratchet 36t internals (10 degs), 100x12mm & 142x12mm, Shim. RD. 11SP HG freehub - Bearing Type: DT Swiss Sealed Steel Cartridge Bearings - Spokes: DT Swiss Competition Race Straightpull, Front: Radial/Two-cross (2:1) 21 count, DS: 276mm, NDS: 290mm; Rear: Two-cross (1:1) 24 count, DS: 283mm NDS: 287mm - Nipple: DT Swiss Hex Prolock Al 2.0x14mm - Tire Size: 24mm—38mm; Max Pressure: 24mm-35mm: Tubeless (110psi) Tubed (130psi), 36mm-38mm: Tubeless (60psi) Tubed (60psi) - Weight: Wheelset 1,375g, Front 606g, Rear 769g (including 15g, tubeless rim tape and tubeless valve) - Assembly Method: Hand built at every step; from rim layup to the last nipple turn. - Extras: Roval Rim Tape, Spare Spoke & Nipple Kit, System Weight Limit: 275lbs/125kg

Feel your bike come alive on the open road with the new Alpinist CL II, featuring the lightest, best-handling clincher rims we have ever made, elevated with the performance of a tubeless system. The brand new Alpinist CL II now brings mountain-taming performance slightly closer to earth with a carefully selected build designed to let riders take full advantage of the low rim and spoke mass. The Alpinist CL II utilizes the same rim as the alpinist clx ii. They react to even the slightest increase in power with immediate acceleration and carve the purest lines in the corners, yet they can also handle almost double the impact standards of every certifying body. The result is a 1375-gram tubeless wheelset with an otherworldly ride quality designed for real-world road pressures. The Alpinist CL II utilizes components curated to keep you rolling and rolling fast. The DT Swiss 350 hubs, featuring their star ratchet drive system, are reliable and easy to service, while 24 DT Swiss comprace straight-pull spokes front and rear, laced to the rims with their alloy pro lock nipples, are synonymous with reliability and can be obtained at any bike shop. The reduced rolling resistance of a tubeless setup is undeniable, as are the benefits of improved handling and incredible puncture protection. It took the most extensive and demanding engineering and testing program we've ever undertaken. As a result of this extensive development, the Alpinist CL II features a hooked rim that can handle a huge range of pressures up to 110psi and offers an easier set up and mounting experience than ever. - Rim: Alpinist CLX Carbon Clincher, 700c, Disc Brake, Tubeless - Rim Details: 33mm Depth, 27mm External Width, 21mm Internal Width - Hub: DT Swiss 350 Straightpull Center Lock, Star Ratchet 36t internals (10 degs), 100x12mm & 142x12mm, Shim. RD. 11SP HG freehub - Bearing Type: DT Swiss Sealed Steel Cartridge Bearings - Spokes: DT Swiss Competition Race Straightpull, Front: Radial/Two-cross (2:1) 21 count, DS: 276mm, NDS: 290mm; Rear: Two-cross (1:1) 24 count, DS: 283mm NDS: 287mm - Nipple: DT Swiss Hex Prolock Al 2.0x14mm - Tire Size: 24mm—38mm; Max Pressure: 24mm-35mm: Tubeless (110psi) Tubed (130psi), 36mm-38mm: Tubeless (60psi) Tubed (60psi) - Weight: Wheelset 1,375g, Front 606g, Rear 769g (including 15g, tubeless rim tape and tubeless valve) - Assembly Method: Hand built at every step; from rim layup to the last nipple turn. - Extras: Roval Rim Tape, Spare Spoke & Nipple Kit, System Weight Limit: 275lbs/125kg

Lighten Your Bike, Not Your Wallet. Conquer mountains, flatten hills, and feel your bike come alive with this ultra-light, 1365 gram wheelset. Mass is the enemy of performance, and the Alpinist CL is the lightest wheelset in its class. Weight has been pared to the absolute minimum to make the make the most of every watt and deliver incredible responsiveness without sacrificing any of the strength, ride quality, or durability that are crucial to long-term performance and satisfaction. - Assembly Method: Hand-built - Braking Surface: Disc brake only - DT Swiss 350, Center Lock, Sealed Cartridge bearings, DT Swiss Star Ratchet internals,142x12mm thru-axle compatible - Extras: Roval padded wheelbag. NoFault crash replacement policy. Lifetime warranty - Nipple Type: DT Swiss Pro Lock hexagonal - Rim Depth: 33mm - Rim Material: Carbon - Rim Type: Carbon, clincher (tube-type) - Rim Width: 21mm internal - Spoke Count: 24F and 24R - Spoke Pattern: Two-cross (1:1) Front and Rear - Spoke Type: DT Swiss Aerolite T-head - Weight: Front - 601g; Rear - 764g

Conquer mountains, flatten hills, and feel your bike come alive with this ultra-light, 1365 gram wheelset. Mass is the enemy of performance, and the Alpinist CL is the lightest wheelset in its class. Weight has been pared to the absolute minimum to make the make the most of every watt and deliver incredible responsiveness without sacrificing any of the strength, ride quality, or durability that are crucial to long-term performance and satisfaction. - Assembly Method: Hand-built - Braking Surface: Disc brake only - Extras: Roval padded wheelbag. NoFault crash replacement policy. Lifetime warranty - Front Hub: Roval AeroFlange Disc, Center Lock, Sealed Cartridge bearings - Nipple Type: DT Swiss Pro Lock hexagonal - Rim Depth: 33mm - Rim Material: Carbon - Rim Type: Carbon, clincher (tube-type) - Rim Width: 21mm internal - Spoke Count: 21 - Spoke Pattern: Radial/Two-cross (2:1) - Spoke Type: DT Swiss Aerolite T-head - Weight: 562g

Feel your bike come alive on the open road with the new Alpinist CLX II-the lightest, best-handling clincher wheels we have ever made. Hyper-responsive acceleration, magic in the corners, sublime over rough roads, all elevated with the performance of a tubeless system. There's no room for a single excess gram whether you're chasing summits or ride quality because perfection is only achieved when there is nothing left to take away. It takes more than a lightweight rim to deliver the incredible reactivity and handling of the tubeless Alpinist CLX II. The wheelset is designed as a system with our engineers controlling and testing every part of that system-hubs, rims, spokes, lacing-and developing it hand-in-hand with Specialized Tubeless tires. The result is a 1250-gram tubeless wheelset with otherworldly ride quality. The Alpinist CLX II utilizes a hooked rim (allowing for real-world riding pressures up to 110psi, if that's your thing) for secure tire bead retention and an easier set up and mounting experience than ever before. All in a wheel that almost doubles current industry impact standards while managing to achieve the lightest weight possible. Our all-new LightAF hubs are the spinning heart of the Alpinist CLX II. We carved 50 grams out of the previous Alpinist CLX hub with new low-profile hub bodies and machined rotor mounts. Inside, DT Swiss EXP internals and SINC ceramic bearings deliver silky-smooth efficiency and outstanding durability. - Rim: Alpinist CLX Carbon Clincher, 700c, Disc Brake, Tubeless - Rim Details: 33mm Depth, 27mm External Width, 21mm Internal Width - Hub: Roval Light Hub (LFD13/LF14R) Center Lock, DT Swiss 180 Ratchet EXP 36t internals (10 degs), 100x12mm & 142x12mm, Shim. RD. 11SP HG freehub - Bearing Type: DT Swiss SINC Ceramic Bearings - Spokes: DT Swiss Aerolite T-head, Front: Radial/One-cross (2:1) 21 count, DS: 276mm, NDS: 290mm; Rear: One-cross/Two-cross (2:1), DS: 288mm NDS: 286mm - Nipple: DT Swiss Hex Prolock Al 2.0x14mm - Tire Size: 24mm - 38mm; Max Pressure: 24mm-35mm: Tubeless (110psi) Tubed (130psi), 36mm-38mm: Tubeless (60psi) Tubed (60psi) - Weight: Wheelset 1,265g, Front 670g, Rear 694g (including 15g, tubeless rim tape and tubeless valve) - Assembly Method: Hand built at every step; from rim layup to the last nipple turn. - Extras: Roval Rim Tape, Spare Spoke & Nipple Kit, System Weight Limit: 275lbs/125kg

Feel your bike come alive on the open road with the new Alpinist CLX II-the lightest, best-handling clincher wheels we have ever made. Hyper-responsive acceleration, magic in the corners, sublime over rough roads, all elevated with the performance of a tubeless system. There's no room for a single excess gram whether you're chasing summits or ride quality because perfection is only achieved when there is nothing left to take away. It takes more than a lightweight rim to deliver the incredible reactivity and handling of the tubeless Alpinist CLX II. The wheelset is designed as a system with our engineers controlling and testing every part of that system-hubs, rims, spokes, lacing-and developing it hand-in-hand with Specialized Tubeless tires. The result is a 1250-gram tubeless wheelset with otherworldly ride quality. The Alpinist CLX II utilizes a hooked rim (allowing for real-world riding pressures up to 110psi, if that's your thing) for secure tire bead retention and an easier set up and mounting experience than ever before. All in a wheel that almost doubles current industry impact standards while managing to achieve the lightest weight possible. Our all-new LightAF hubs are the spinning heart of the Alpinist CLX II. We carved 50 grams out of the previous Alpinist CLX hub with new low-profile hub bodies and machined rotor mounts. Inside, DT Swiss EXP internals and SINC ceramic bearings deliver silky-smooth efficiency and outstanding durability. - Rim: Alpinist CLX Carbon Clincher, 700c, Disc Brake, Tubeless - Rim Details: 33mm Depth, 27mm External Width, 21mm Internal Width - Hub: Roval Light Hub (LFD13/LF14R) Center Lock, DT Swiss 180 Ratchet EXP 36t internals (10 degs), 100x12mm & 142x12mm, Shim. RD. 11SP HG freehub - Bearing Type: DT Swiss SINC Ceramic Bearings - Spokes: DT Swiss Aerolite T-head, Front: Radial/One-cross (2:1) 21 count, DS: 276mm, NDS: 290mm; Rear: One-cross/Two-cross (2:1), DS: 288mm NDS: 286mm - Nipple: DT Swiss Hex Prolock Al 2.0x14mm - Tire Size: 24mm - 38mm; Max Pressure: 24mm-35mm: Tubeless (110psi) Tubed (130psi), 36mm-38mm: Tubeless (60psi) Tubed (60psi) - Weight: Wheelset 1,265g, Front 670g, Rear 694g (including 15g, tubeless rim tape and tubeless valve) - Assembly Method: Hand built at every step; from rim layup to the last nipple turn. - Extras: Roval Rim Tape, Spare Spoke & Nipple Kit, System Weight Limit: 275lbs/125kg

Conquer mountains, flatten hills, and feel your bike come alive with this ultra-light, 1365 gram wheelset. Mass is the enemy of performance, and the Alpinist CL is the lightest wheelset in its class. Weight has been pared to the absolute minimum to make the make the most of every watt and deliver incredible responsiveness without sacrificing any of the strength, ride quality, or durability that are crucial to long-term performance and satisfaction. - Assembly Method: Hand-built - Braking Surface: Disc brake only - Extras: Roval padded wheelbag. NoFault crash replacement policy. Lifetime warranty. - Nipple Type: DT Swiss Pro Lock hexagonal - Rear Hub: Roval AeroFlange Disc, Center Lock, Sealed Cartridge bearings, DT Swiss EXP internals, HG Freehub, 142x12mm thru-axle compatible - Rim Depth: 33mm - Rim Material: Carbon - Rim Type: Carbon, clincher (tube-type) - Rim Width: 21mm internal - Spoke Count: 24 - Spoke Pattern: One-cross/Two-cross (2:1) - Spoke Type: DT Swiss Aerolite T-head - Weight: 686g

First came our CLX 64. Then the 32s. And after racking up multiple wins in Grand Tours, Worlds, and everything in between, we knew that our best bet was to take the line to new heights, or well, new depths. We needed to design one wheel that was a true quiver killer. One wheel that had all the aerodynamic benefits of the 64 in a package that climbed like the 32, and that’s where the all-new CLX 50 comes in. When we set out to create the CLX 50 Disc, we had clear goals in mind—create wheels that are 48 to 54mm deep, aerodynamically optimized, ultra-wide, and under 1400 grams. This meant that they'd have to borrow some weight savings techniques that we developed for the CLX 32, take some aero guidance from the CLX 64, and keep all of the disc brake benefits that we've come to love if we were going to create what we like to call "the unicorn wheel." Why discs you ask? With our disc-specific rims, we ditch the brake track, making for a stronger, more impact-resistant rim. This way, you get a disc-specific carbon layup that optimizes stiffness, a weight as close to its rim-brake brethren as possible, and incredible brake modulation and power in all conditions. Even though the CLX 50 is similar in weight to many wheels in the "lightweight" category, aerodynamics came at the forefront of the development. With this, we jumped headlong into Computational Fluid Dynamics computer modeling to arrive at various rim shapes that could make the CLX 50 as fast and light as possible. It took a while, but we narrowed the rim shape down to three contenders that were then CNC-machined into rims, built into wheels, and put into the Win Tunnel. In the tunnel, we tested every wheel, ours and the competition's, with a 24C tire (measuring 26C), as tires can drastically affect testing. We chose a modern-width tire to design our rims around because they not only allow for less tire pressure (which results in more comfort and less rolling resistance) but are also just as aerodynamically efficient when paired with the correct rim width. After finding the optimized rim shape that best supported our svelte weight requirements, we opted to lace the rims to our Aero Flange (AF) hub, via 21 DT Swiss Aerolite spokes, which features the legendary CeramicSpeed bearings. This way you get a complete, superior wheel system—not just a quick rim. And at the end of the day, it all amounts to a 50mm-deep, 1415-gram clincher disc wheelset that's not only ~300 grams lighter than the competition’s similar depth wheel, but is also measurably faster in every conceivable test than each wheel in its category.

First came our CLX 64. Then the 32s. And after racking up multiple wins in Grand Tours, Worlds, and everything in between, we knew that our best bet was to take the line to new heights, or well, new depths. We needed to design one wheel that was a true quiver killer. One wheel that had all the aerodynamic benefits of the 64 in a package that climbed like the 32, and that's where the all-new CLX 50 comes in. When we set out to create the CLX 50 Disc, we had clear goals in mind, create wheels that are 48 to 54mm deep, aerodynamically optimized, ultra-wide, and under 1400 grams. This meant that they'd have to borrow some weight savings techniques that we developed for the CLX 32, take some aero guidance from the CLX 64, and keep all of the disc brake benefits that we've come to love if we were going to create what we like to call "the unicorn wheel." Why discs you ask? With our disc-specific rims, we ditch the brake track making for a stronger, more impact-resistant rim. This way, you get a disc-specific carbon layup that optimizes stiffness, a weight as close to its rim-brake brethren as possible, and incredible brake modulation and power in all conditions. Even though the CLX 50 is similar in weight to many wheels in the "lightweight" category, aerodynamics came at the forefront of the development. With this, we jumped headlong into Computational Fluid Dynamics computer modeling to arrive at various rim shapes that could make the CLX 50 as fast and light as possible. It took a while, but we narrowed the rim shape down to three contenders that were then CNC-machined into rims, built into wheels, and put into the Win Tunnel. In the tunnel, we tested every wheel, ours and the competition's, with a 24C tire (measuring 26C), as tires can drastically affect testing. We chose a modern-width tire to design our rims around, because they not only allow for less tire pressure (which results in more comfort and less rolling resistance) but are also just as aerodynamically efficient when paired with the correct rim width. After finding the optimized rim shape that best supported our svelte weight requirements, we opted to lace the rims to our Aero Flange (AF) hub, via 24 DT Swiss Aerolite spokes, which features the legendary CeramicSpeed bearings. This way you get a complete, superior wheel system, not just a quick rim. And at the end of the day, it all amounts to a 50mm-deep, 770-gram rear wheel that's not only significantly lighter than the competition's similar depth wheel, but is also measurably faster in every conceivable test than each wheel in its category. - Assembly Method: Hand-built - Braking Surface: Disc brake only - Extras: Roval padded wheelbag, Roval steel quick-release, Roval tubeless plugs and tubeless valve,142x12mm thru-axle, quick-release end caps - Nipple Type: DT Swiss Pro Lock hexagonal - Rear Hub: Roval AFD2, Center Lock, CeramicSpeed bearings, DT Swiss 240 internals, 11-speed, quick-release or 142x12mm thru-axle end cap - Rim Depth: 50mm - Rim Material: Carbon - Rim Type: Carbon clincher, 2Bliss Ready - Rim Width: 20.7mm internal, 29.4mm external - Spoke Count: 24 - Spoke Pattern: One-cross/Two-cross (2:1) - Spoke Type: DT Swiss Aerolite T-head - Weight: 770g

Performance Upgrade Made Easy The C38 brings carbon fiber high performance to the real world. It's a versatile all-rounder equally at home crushing gravel washboards and summiting alpine passes. Optimized for use with modern wide tires, providing the right amount of sidewall support to facilitate surefooted handling in all conditions, the C38 wheelset is a great handling, lively climbing, robust all-road performer that also aerodynamically outperforms many deeper, aero-specific rims that cost twice as much. Carbon wheels are a true performance upgrade to any bike, but too often the price tag puts them out of reach. The Rapide C38 shatters that barrier and brings a class-leading Roval carbon rim and DT Swiss reliability together to provide riders with the best performance carbon wheel per dollar.

Since 2020, Rapide CLX wheels have won more races on the world tour than any other wheels, and we just made them faster. Meet the new Rapide CLX II. Combining the aerodynamics of a deep-section TT wheel with the light weight of a shallower climbing wheel and mixing in the superior efficiency and sublime handling of a tubeless system-the Rapide CLX II delivers maximum speed for real-world riding. We developed distinctly different shapes for the Rapide CLX II front and rear rims. The result is a wheelset that catches less drag than most 65mm wheelsets and brings a dramatic 25% improvement in stability over 50mm rims in wind gusts. The Rapide CLX II utilizes a hooked rim (allowing for real-world riding pressures up to 110psi, if that's your thing) for secure tire bead retention and an easier set up and mounting experience than ever before. All in a wheel that almost doubles current industry impact standards while managing to achieve the lightest weight possible. Our aeroflange hubs are aerodynamically optimized, with wide bracing angles for increased strength and reduced spoke weight. They also benefit from the reduced weight and increased strength of ceramic sinc bearings and the legendary durability of DT Swiss exp freehub internals. - Rim: Rapide CLX Carbon Clincher, 700c, Disc Brake, Tubeless Rim Details: 51mm Depth, 35mm External Width, 21mm Internal Width - Hub: Roval Aero Hub (AFD01/AFD02R) Center Lock, DT Swiss 180 Ratchet EXP 36t internals (10 degs), 100x12mm & 142x12mm, Shim. RD. 11SP HG freehub - Bearing Type: DT Swiss SINC Ceramic Bearings - Spokes: DT Swiss Aerolite T-head, Front: Radial/One-cross (2:1) 18 count, DS: 257mm, NDS: 252mm; Rear: One-cross/Two-cross (2:1) 24 count, DS: 243mm NDS: 249mm - Nipple: DT Swiss Hex Prolock Al 2.0x14mm - Tire Size: 24mm—38mm; Max Pressure: 24mm-35mm: Tubeless (110psi) Tubed (130psi), 36mm-38mm: Tubeless (60psi) Tubed (60psi) - Weight: Wheelset 1,520g, Front 710g, Rear 810g (including 15g, tubeless rim tape and tubeless valve) - Assembly Method: Hand built at every step; from rim layup to the last nipple turn. - Extras: Roval Rim Tape, Spare Spoke & Nipple Kit, System Weight Limit: 275lbs/125kg

Since 2020, Rapide CLX wheels have won more races on the world tour than any other wheels, and we just made them faster. Meet the new Rapide CLX II. Combining the aerodynamics of a deep-section TT wheel with the light weight of a shallower climbing wheel and mixing in the superior efficiency and sublime handling of a tubeless system-the Rapide CLX II delivers maximum speed for real-world riding. We developed distinctly different shapes for the Rapide CLX II front and rear rims. The result is a wheelset that catches less drag than most 65mm wheelsets and brings a dramatic 25% improvement in stability over 50mm rims in wind gusts. The Rapide CLX II utilizes a hooked rim (allowing for real-world riding pressures up to 110psi, if that's your thing) for secure tire bead retention and an easier set up and mounting experience than ever before. All in a wheel that almost doubles current industry impact standards while managing to achieve the lightest weight possible. Our aeroflange hubs are aerodynamically optimized, with wide bracing angles for increased strength and reduced spoke weight. They also benefit from the reduced weight and increased strength of ceramic sinc bearings and the legendary durability of DT Swiss exp freehub internals. - Rim: Rapide CLX Carbon Clincher, 700c, Disc Brake, Tubeless Rim Details: 51mm Depth, 35mm External Width, 21mm Internal Width - Hub: Roval Aero Hub (AFD01/AFD02R) Center Lock, DT Swiss 180 Ratchet EXP 36t internals (10 degs), 100x12mm & 142x12mm, Shim. RD. 11SP HG freehub - Bearing Type: DT Swiss SINC Ceramic Bearings - Spokes: DT Swiss Aerolite T-head, Front: Radial/One-cross (2:1) 18 count, DS: 257mm, NDS: 252mm; Rear: One-cross/Two-cross (2:1) 24 count, DS: 243mm NDS: 249mm - Nipple: DT Swiss Hex Prolock Al 2.0x14mm - Tire Size: 24mm—38mm; Max Pressure: 24mm-35mm: Tubeless (110psi) Tubed (130psi), 36mm-38mm: Tubeless (60psi) Tubed (60psi) - Weight: Wheelset 1,520g, Front 710g, Rear 810g (including 15g, tubeless rim tape and tubeless valve) - Assembly Method: Hand built at every step; from rim layup to the last nipple turn. - Extras: Roval Rim Tape, Spare Spoke & Nipple Kit, System Weight Limit: 275lbs/125kg

We believe we've made the fastest all-around road wheels in the world. The Rapide CLX wheelset essentially combines the aerodynamic excellence of our UCI TT World Championship dominating CLX64 with the light weight and gentlemanly handling of our Polkadot-Jersey winning CLX32. The result is a wheelset that delivers maximum speed in conditions found in real-world riding; climbing performance, slippery efficiency of a dedicated aero setup, and stable, confident handling, regardless of wind conditions. - Assembly Method: Hand-built - Braking Surface: Disc brake only - Extras: Roval padded wheelbag. NoFault crash replacement policy. Lifetime warranty. - Nipple Type: DT Swiss Pro Lock hexagonal - Rear Hub: Roval AeroFlange Disc, Center Lock, Sealed Cartridge bearings, DT Swiss EXP internals, HG Freehub, 142x12mm thru-axle compatible - Rim Depth: 60mm - Rim Material: Carbon - Rim Type: Carbon, clincher (tube-type) - Rim Width: 21mm internal, 30.7mm external - Spoke Count: 24 - Spoke Pattern: One-cross/Two-cross (2:1) - Spoke Type: DT Swiss Aerolite T-head - Weight: 751g

One wheel to rule all roads. Road light, off-road tough, smooth as butter, Terra CLX wheels bring leading-edge performance to the diverse needs of mixed-terrain rides. These are the lightest gravel wheel on the market. They sport 25mm internal-width rims, deliver a durable and exceptionally smooth ride, are compatible with 28-42mm tires at up to 90 PSI, and they come with a lifetime warranty and no-fault crash replacement. - Rim Type: Carbon Clincher, tubeless-first - Rim Material: Advanced Carbon Composite - Rim Width (internal): 25mm - Rim Depth: 32mm - Front Spoke Pattern: Radial/Two-cross (2:1) - Spoke Count: 21 - Spoke Type: DT Swiss Aerolite T-head - Nipple Type: DT Swiss Pro Lock Alloy hexagonal - Spoke Length: Right/Left: 276mm/274mm - Front Hub: Roval AFD1, Center Lock, 12mm thru-axle end cap - Assembly Method: Handbuilt - Extras: Roval padded wheelbag, Roval tubeless rim tape and valves (pre-installed) - Wheelset Weight (front and rear with rim tape and tubeless valves): 1296g

One wheel to rule all roads. Road light, off-road tough, smooth as butter, Terra CLX wheels bring leading-edge performance to the diverse needs of mixed-terrain rides. These are the lightest gravel wheel on the market. They sport 25mm internal-width rims, deliver a durable and exceptionally smooth ride, are compatible with 28-42mm tires at up to 90 PSI, and they come with a lifetime warranty and no-fault crash replacement. - Rim Type: Carbon Clincher, tubeless-first - Rim Material: Advanced Carbon Composite - Rim Width (internal): 25mm - Rim Depth: 32mm - Rear Spoke Pattern: One-cross/Two-cross (2:1) - Spoke Count: 24 - Spoke Type: DT Swiss Aerolite T-head - Nipple Type: DT Swiss Pro Lock Alloy hexagonal - Spoke Length: Drive-Side/Non-Drive: 272mm/277mm - Rear Hub: Roval AFD2, Center Lock, DT Swiss EXP internals, Shimano HG, 142x12mm thru-axle end cap - Assembly Method: Handbuilt - Extras: Roval padded wheelbag, Roval tubeless rim tape and valves (pre-installed) - Wheelset Weight (front and rear with rim tape and tubeless valves): 1296g

Trail wheels often fall into two categories—they're either heavy and durable or light and flexy. And because of this, a lightweight, wide-profile, and enduro-ready carbon wheel seems like something only found in a fairytale, but lucky for you, we made it a reality. The Traverse SL Fattie 29 puts all the features you need in an all-mountain wheel into one package, and it has the results to prove it. Along with light overall weight, stiffness, and durability, another top priority for the Traverse SL was ease of use. First off, we got rid of the creaky straight-pull spokes and corrosion-prone alloy nipples. Next up, we landed on 28 J-bend spokes, for both the front and rear wheels, that are all the same length—making it easy to find replacements if needed. And finally, we engineered a new hub design, with a wider profile and higher flange to aid in overall stiffness. What's with the big-boned name, you ask? The Traverse SL Fatties may be wide, but with a 30mm inner rim width, they're far from the girth of a fat bike rim. But let's talk width. You've probably noticed that mountain bike rim widths have hovered between 19 and 23 millimeters for decades, and they've been long overdue for a change. In the search for a better wheel design, our engineers began testing 2.3- to 2.5-inch tires on 45-millimeter-wide fat bike rims to see what, if any, benefits could be found. It only took them a few rides to realize that the wider rims offered a variety of advantages, like adding additional tire volume, which better supports the tires in hard cornering, greatly improves traction because of the ability to run lower pressures, and noticeably increases rim stiffness. They did note that there is an occurrence of diminishing returns with increasing width, however, and after testing everything from 25 to 45mm, determined that a 30mm inner width is optimal. After determining the width, we began designing the rim using the knowledge that we gained when developing the Control SL. With this, we started with our Zero Bead Hook technology that gets rid of the weak spot found in a traditional wheel and combined it with the wider profile to make a carbon rim that effectively dissipates forces. This way, you can take abuse from rocks without the worry of cracks or dents. Ok, so they're strong, impact-resistant, and tire supporting-they must be heavy, right? Wrong. Even though "fattie" is in their name, they're far from fat. To achieve this weight, we hand-build our rims to our own alloy hubs, using only the highest quality DT Swiss Competition Race spokes. Inside our hubs, you'll find DT Swiss 240 internals with a quick engaging 54t DT Swiss star ratchet system in the rear that allows you to power over rocks and roots without delay. And while machines do a pretty good job of building wheels, we choose professionally trained humans because they do so with an artistic touch that makes for minimal flaws. Whether you need a carbon wheelset to get you through an enduro stage or one to shred your local rock garden, the Traverse SL Fattie has you covered. - Assembly Method: Hand-built - Bearing Type: Sealed cartridge - Every wheel includes tubeless valve stems in order to make tubeless set-up a touch easier. - Front Hub: Alloy body, 15mmx110 thru-axle, 19 and 31mm OD end cap options included. - Front Spoke Pattern: Two-cross - Nipple Type: DT Swiss Brass Pro Lock hexagonal - Rim Material: Carbon fiber - Rim Type: Carbon clincher, 2Bliss Ready, Zero Bead Hook design. Black graphic under clear coat. - Rim Width: 30mm internal - Roval Engineered J-bend hubshells have a single spoke length for each wheelset. - Spoke Count: 28h Front - Spoke Type: DT Swiss Competition Race J-bend

Roval's rim-specific Tubeless Valves are designed to match Specialized's rim profiles and provide a better seal than previous generation valves. - Constructed of lightweight aluminum - Removable valve core - Mated with a seal which is specific to different rim models: - MY14 Control SL = black rim bed shaped seal - MY15 Control Carbon/Aluminum = red rim shaped seal - MY15 Traverse SL/Aluminum = black O-ring seal

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

The best price on the market for a wheel meant to be ridden. Single-wall rims and loose-ball hubs that come out of the box round and true.

The best price on the market for a wheel meant to be ridden. Single-wall rims and loose-ball hubs that come out of the box round and true.

The best price on the market for a wheel meant to be ridden. Single-wall rims and hubs that come out of the box round and true. - 25mm external rim width

The best price on the market for a wheel meant to be ridden. Single-wall rims and hubs that come out of the box round and true.

Quality Wheels Value Series Disc Front Wheel 29 SRAM 406 6-bolt / Sun SR25 Black

Our best value in Quick-release disc wheels.

The standard in basic mid-range hybrid repair wheels.

Similar to the stock wheel for Surly's Long Haul Trucker.

If you need just one wheel for on-the-spot repairs, this wheel features both rim brake and disc brake compatibility.

When top EWS Pro Riders ask you to develop a stiffer more durable fork axle, you listen. The stock 15mm axles and other lightweight aftermarket options were simply not tough enough for their race bikes. We don't quite ride at the pace of an EWS Pro, but we loved the simplicity and clean look of the axle so we made them available to buy. Axle F is 98% stronger and stiffer than a stock 15mm axle, yet still 20g lighter than a QR. We've replaced the QR lever with a simple 6mm hex. If you already carry the EDC multitool with you, there's no need for the heavy and bulky QR lever. FEATURES - 98% Stiffer and stronger than stock 15mm QR thru axle - 20g Lighter than stock QR thru axle - Low profile hex head won't get caught on trailside obstacles. COMPATIBILITY - For Fox and RockShox 15mm axle forks (Boost and Non Boost) - NOT compatible with RockShox RS-1 fork or Fox 36 Pinch Bolt Style (2016 and older) - NOT compatible with floating thru axles from 2021 Fox 36, 38 or 40 WEIGHT - RockShox Boost (15x110) 63g - RockShox Non Boost (15x100) 59g - Fox Boost (15x110) 61g - Fox Non Boost (15x100) 58g MATERIAL - 6061-T6 Aluminum

One of the most celebrated rims in the history of road cycling, Mavic’s Open Pro remains the example to which high-end aluminum road rims are compared. Its design is tried and true, and its Maxtal material delivers a perfectly balanced strong, rigid, and lightweight wheel build. It also features Mavic’s Soudé Usiné Process (SUP), a process by which the rim is arc welded and machined smooth, resulting in a stronger rim joint and better rim balance, as well as smooth, shudder-free braking. Ride a pair of Open Pros and you’ll understand why so many experienced riders swear by them. - Clincher

Protect your tubes without adding bulk with these Rim Strips from FSA. They're lightweight, and come in different lengths according to wheel size. Peace-of-mind comes standard.

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

- Extra security against theft - 5mm hex CrMo axle

- Bladed Competition spokes 2.0/.09x2.3/2.0mm, black surface treatment resists scratches - Cold forging technology, CrNi stainless steel with rolled threads - No hub slotting necessary - 190g (32/265mm) - Box of 20 - Nipples sold separately

- Bladed Revolution spokes 2.0/.09x2.3/2.0mm, black surface treatment resists scratches - Cold forging technology, CrNi stainless steel with rolled threads - No hub slotting necessary - 139g (32/265mm) - Box of 20 - Nipples sold separately

- Bladed Revolution spokes 2.0/.09x2.3/2.0mm, white surface treatment resists scratches - Cold forging technology, CrNi stainless steel with rolled threads - No hub slotting necessary - 139g (32/265mm) - Box of 20 - Nipples sold separately

- Straight gauge 2.0mm with cold forging technology - Chrome nickel stainless steel with rolled threads. Black surface treatment resists scratches - 222g @ 32h/265mm - Box of 72 - Nipples sold separately

- Straight gauge 2.0mm with cold forging technology - Chrome nickel stainless steel with rolled threads - 222g @ 32h/265mm - Box of 100 - Nipples sold separately

Champion 2.0 Black Spokes - One 264mm spoke = 7g

This is one of the most versatile spokes in the DT Swiss spoke range. DT competition gets its special strength from cold forging. This makes an extremely durable spoke and thanks to the thinner middle section, it is 48 g lighter (per 64 spokes) than a spoke with a constant diameter of 1.8 mm. It is perfect for a wide range of uses, from road wheels to super light enduro MTB wheels. - Double Butted: 2.0/1.8/2.0 - One 264mm spoke = 6g - Nipples sold separately